how to see mac address-table with interface on cisco 3750 switches
in our cisco 3750 switch if I run the command show mac address-table it shows the mac address table with port chaneel number (po1) not the individul interfaces (ie. gi1/0/1, gi1/0/2, etc...). what is command to show the individual interfaces. Because I need to find the interfaces that connected to the printers by using MAC addresses of the ...
Cisco 3750 VLAN Internet Connection - Cisco Learning Network
Normally this would not reach the hosts in Vlan 10 or Vlan 20 because this broadcast would be stopped by the 3750. However, with proxy arp enabled on Vlan1 (again, by default), the 3750 will reply to the ARP request on behalf of vlan10 and vlan20-based hosts. In this way, the Interwebs router will send ethernet frames to the 3750.
Cisco 3750 Netflow Config - Cisco Learning Network
Hi Jeremiah! I believe you need to have a 3750-X switch or else no Flexible NetFlow for you bro! The full proto is supported on routers and some Catalyst switches (3560-X, 3750-X, 4500, 6500) as you can see in the following links:
catalyst 3750 - Cisco Learning Network
If your switch is 3750-x, this doc has the password recovery procedure. Catalyst 3750-X and 3560-X Switch Software Configuration Guide, Release 12.2(53)SE2 - Troubleshooting [Cisco Catalyst 37… Procedure with Password Recovery Enabled . If the password-recovery mechanism is enabled, this message appears:
TCAM demystified - Cisco Learning Network
One of the key components of virtually any layer 2 or layer 3 switch is the Ternary Content Addressable Memory, or TCAM in short. TCAM is an expensive component and is typically a scarce resource on many switching platforms. This especially holds true on lower-end platforms such as the 3560-X/3750-X, where the administrator must make a decision ...
SFP Not supported - 3750 - Cisco Learning Network
Edited by Admin February 16, 2020 at 3:13 AM. SFP Not supported - 3750. Hi All, After inserting SFP transceiver module, the console displays. %PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi1/0/2 is not supported. I assume the transceiver module I bought is …
How to configure RADIUS using Server 2012 NPS on 3750 Switch
You want the radius servers be used for authentication of logins via telnet or ssh? I think, something like this should work: aaa group server radius myradius. server x.x.x.x auth-port 1812 acct-port 1813. server y.y.y.y auth-port 1812 acct-port 1813. aaa authentication login default group myradius local.
AAA Radius Issue - Cisco Switch 3750 - Cisco Learning Network
Hi Guys, I have an issue using AAA Radius with the Catalyst 3750. I have checked the configuration several times and I've also tried different configuration and I always come across with the same problem. It seems that somehow the switch is not receiving or accepting the return response from Windows Server 2012.
How can we emulate Cisco 3850 and 3750 layer 3 switches on PT
Hello everyone, I'm quite new with PT, I'm a student in some Audiovisual School, and i'm in charge of the network part. I'm trying to make my Audiovisual school's network Topology on PT, but i got a few problems. We are using Layer 3 Switches as Cisco 3850 and Cisco 3750, but they're not available in PT, do you know a way to emulate them or ...
How to emulate a switch on gns3 - Cisco Learning Network
Cisco Admin. Body. Hi guys, after some research with a friend, we can successfully simulate a switch. 1 - Install gns3 (); 2 - try to get the c3725-adventerprisek9-mz.124-15.T14 from your sources; 3 - open the gns3 and go to edit > symbol manager. Add the ethernet_switch, double click on it on right bar, and select router c3700 on type, apply, OK.