Help: problem with old Craftsman 100 table saw - Woodworking …
Jan 14, 2012 · Today, I picked up my first table saw - a VERY old Craftsman 100 10" model. I have had good luck with other older power tools, which I like because they are built like TANKS (my old jointer is great) and are cheap on Craigslist. I got it home, plugged it in, and tried running a 1/2" inch pine board through it.
Vintage craftsman 100 tablesaw - Woodworking Talk
Sep 28, 2022 · That same model saw was my very first table saw. I bought it with high school graduation gift money when I was 18 years old, 1960. I loved it and used it for about 45 years. It never really wore out, but I did replace the arbor bearings twice. The fence is a rack and pinion system and is pretty accurate, if I recall.
Help with Craftsman 100 table saw motor replacement
Jan 28, 2017 · My first table saw was a Craftsman 100, circa 1960's I used it for about 40+ years and finally parted it out. The motor mount is a hinged affair, where the weight of the motor keeps the belt under tension. It is NOT a "tight as you can make it" arrangement like some other saws.
Restoring Craftsman model 100 table saw - Woodworking Talk
Jun 13, 2011 · That's an ancient motor. I have a 1 HP motor, that powered my 10" Craftsman 100 saw, a small red reset button on the motor housing. It's possible to eliminate that part and use a on/off switch with a overload breaker built in. Should draw about 10 to 12 amps for a 3/4HP motor so size the switch accordingly.
Dust control on vintage table saw - Woodworking Talk
May 7, 2020 · My old Craftsman model 100 saw on its open square stand with only a three sided cardboard box fitted into the lower stand makes almost no dust other than what falls off the table or spills out of the box. It never fills the air with dust to the point I can't breath.
Old Craftsman 10" table saw - Woodworking Talk
Feb 4, 2010 · I purchased and old (manual printed April, 1996) 220 volt, 10", cast iron Craftsman table saw at a garage sale. It runs and cuts great but the fence is a piece of crap. The table is 30" wide and the model number is 113.298844. The saw cost $150. I would like to keep the fence cost at or below that if possible.
Craftsman Radial 100 question. - Woodworking Talk
Jun 1, 2013 · I would sure want more table length on the left side (facing the saw) of the saw, for cutting 8-10' boards to shorter length. In my shop, I mounted the saw at an angle,so longer boards, stick out the barn door. Crosscutting long boards is one of the things a ras does great.
Riving knife for old craftsman tablesaw? - Woodworking Talk
Aug 24, 2022 · here is link for the manual craftsman 113.299410 manual large scan Since the mid 1980's, virtually every table saw sold in this country (USA) has been equipped with some kind of "splitter", a stationary metal blade intended to hold the kerf open behind the blade.
Craftsman table saw - technical question | Woodworking Talk
Nov 2, 2024 · 2 companion videos from April 2013 by Jamey Saunders; an old Craftsman saw from 1969 (Model 113.29940). Craftsman Table Saw Arbor Rebuild - Part 1: Disassembly Craftsman Table Saw Arbor Rebuild - Part 2: Reassembly and Results In both sets of videos, it’s clear that the 2 bearings are, in fact, sealed.
Craftsman 1950s model table saw - Woodworking Talk
Mar 4, 2012 · I had an old Craftsman 100, the gold one, 10" saw which had a 1 HP Craftsman motor on and it worked well for about 50 years. It was heavy and the fence kinda wiggled but I used it anyhow. If this saw has a real 3HP motor and it says so on the motor, not on the saw, it will be wired for 240 Volts.